Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Manual de usuario Pagina 112
- Pagina / 148
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER 9 SETUP OUTPUT COMMUNICATIONS 111
Figure 9.2 – Select Output Format for Advance (left) and Advance Extended Range (right)
Note
SmartSensor Advance Extended Range only works with the Click 112/114/104 cards. It
does not work with the Click 172/174/100 cards.
In standard installations, either the rst or second option will automatically be selected
when you auto-congure an attached Click detector rack card. e rst option will be se-
lected if you are using a Click 112/114 and the second option will be selected if you are us-
ing a Click 172/174. With version 3.0.2 and later, the default port is set at 2 and the default
format is Z4 - Click 112/114.
e Track File option is not used for standard intersection trac control, but can be used
for other applications. e Track File option will push the range and speed of all detections
as a heartbeat message.
Specify output minimum duration
is option allows you to specify the minimum output duration in seconds. e minimum
output duration is the minimum amount of time that a channel output will be on, even
if the output conditions are removed. e selected value should meet the timing require-
ments of any device in the system that will be processing channel outputs. e default value
of 0.13 seconds works well for most devices. e minimum value is 0.01 seconds and the
maximum value is 5.00 seconds.
Specify output frequency
is allows you to specify the output frequency of all heartbeat (contact closure & track
le) messages in seconds. e specied value determines the time interval between output
transmissions. e selected value should meet the timing requirements of any device in the
system that will be processing channel outputs. e default value of 0.13 seconds works
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Relacionado con productos y manuales para Sensores Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
Sensores Wavetronix VDR24 Radar Manual de usuario
(78 paginas)
(78 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales