Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Manual de usuario Pagina 128
- Pagina / 148
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER 11 TOOLS 127
Status
e Status eld indicates whether the rack card is operating normally or whether it is in
fail-safe mode. If the device is in fail-safe mode, the text message may help you understand
why the device is in fail-safe. For example, if the text reads “Failsafe Initializing,” this indi-
cates that the rack card has never seen any detection call messages since it was rebooted.
If the message reads “Failsafe Timeout (No Data),” this indicates that the rack card was
previously receiving detection calls, but hasn’t received any in the last 10 seconds or more.
Firmware Version
e Firmware Version eld lists the version of the rack card rmware. When you would
like to refresh the status of these elds, click the associated Refresh button. If you are com-
municating with all devices, the status and rmware version elds are not applicable (N/A).
Signal Cards Switch
You can use the Signal Cards toggle switch to help single out devices. When the switch is
ON, all main menu LEDs on the selected devices will begin ashing. If you have selected
All Rack Cards, then the main menu LEDs of every card connected on the bus will begin
ashing.
Channel Outputs Switch
e Channel Outputs toggle switch and 1–16 checkboxes are used to help assist in testing
of the rack card outputs. Even though the SmartSensor Advance only has 8 outputs, the 16
outputs are shown because SmartSensor Advance and SmartSensor Matrix can share the
same control bus. is tool allows you to test communications to rack cards from either
sensor.
If the Channel Outputs switch is ON, all the selected channel outputs on the Click 112/114
rack card will be active. e LEDs that indicate an active output channel will light up ac-
cordingly. An output will only be active when the corresponding box is checked.
Note
When the Rack Card Tool connects, it will disable data push on all sensor ports. This
will normally put the rack card tool into fail-safe mode until you manually activate
channel outputs or close the connection.
e Channel Outputs switch can be very helpful in verifying the I/O channel mapping
from the rack card outputs to the trac controller inputs. By sequentially checking boxes
1–16, you should be able to quickly verify the mapping of each channel, even in the absence
of trac.
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Relacionado con productos y manuales para Sensores Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
Sensores Wavetronix VDR24 Radar Manual de usuario
(78 paginas)
(78 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales