Wavetronix Command Collector (CMD-DCx) - User Guide Manual de usuario Pagina 36
- Pagina / 117
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER 4 SENSOR TOOLBAR 35
2 Enter the IP/Hostname of the sensor or communication server and the Port number
through which Collector will communicate. Ranges can be used to add more than one
sensor at the same time (see Figure 4.3).
Figure 4.3 – Add Sensor Info Fields
Depending on the sensor and communication setup, a multi-drop ID or a unit address
may be required. e Multi-drop ID eld will not be displayed if it is not necessary for
the selected driver. In other cases, the Multi-drop ID eld will be visible and relabeled
with a new name to correspond to the particular address or eld name used by the
device for user clarity.
e Custom ID eld is optional and can be used to enter any additional identication
information.
3 Enter the initial collection interval (in seconds) into the Collection Interval eld. For
sensor drivers that support automatic querying of the sensor interval, the Use Sensor
Interval option will be displayed. Check this box to use the sensor interval as the col-
lection interval.
4 Select the time zone that the sensor resides in from the Time Zone drop-down list and
mark whether the sensor location observes daylight savings time. is will allow Col-
lector to adjust sensor time to local time for proper timekeeping and data storage (see
Figure 4.4).
Figure 4.4 – Additional Add Sensor Fields
e Start Collecting Data Immediately option determines whether data collection is
started or stopped for the new sensor once it is added. If the communication pathway
to the sensor is open, data collection can begin immediately; if the Start Collecting
Data Immediately option is checked, Collector will attempt to retrieve the sensor’s
conguration aer it is added to the system. However, if the sensor is not connected
and congured properly, it is recommended that this option be turned o. If the op-
tion is not turned o, Collector will continue to attempt to connect and will simply log
errors aer every collection interval.
e Attach to Multi-drop Server (if available) option is used when multiple sensors
share a common IP address and port. is option will only be available if the selected
- Command Collector 1
- Contents 4
- Chapter 8 Help Page 103 5
- Introduction 6
- Data Storage 7
- Installing Command HQ 1 8
- Wavetronix representative 10
- Install button 12
- Command Licensing 13
- Oine Activation 14
- In this chapter 18
- Logging In 18
- Service Not Started Errors 19
- Common Web Interface Features 20
- Navigation/Status Control 21
- Web Interface Context Help 22
- Sensors Page 3 24
- Sensor List 25
- Network(s) 27
- Location 28
- Description 28
- Interval (Intrvl) 28
- Frequency (Fq) 28
- Figure 3.5 – Paging Control 29
- Display Settings Control 30
- Filter Controls 31
- With Com Status 32
- With Data Status 32
- Figure 3.10 – By Data Filter 33
- Sensor Toolbar 4 34
- Add Sensors 35
- Modem Support Using COM Ports 37
- Adding Ranges of Sensors 37
- Adding from an Address Book 38
- Remove Sensors 39
- View Errors 39
- Sensor Error Display Settings 40
- Sensor Error Queries 41
- Exporting Sensor Errors 41
- Collection 43
- Intervals 43
- Commands 45
- Networks 46
- Figure 4.18 – Search Box 48
- Figure 4.19 – Search Results 48
- Sensor Configuration Page 5 50
- Sensor Info Bar 51
- Com Status 52
- Data Status 52
- Communication Status Graph 52
- Data Status Graph 53
- Sensor Information 54
- View Log Button 54
- Sensor Config Tab 55
- Custom Configuration Panel 56
- Figure 5.7 – Basic Tab 57
- Figure 5.8 – Advanced Tab 58
- Lanes/Approaches Tab 59
- Setting Custom Lane IDs 60
- Approaches 60
- Sensor Commands Tab 61
- Data Query Tab 63
- Data Query Graphs 64
- Data Query Tables 65
- Data Page 6 68
- Selecting Sensors 69
- Define and Request Report 69
- Output Report Type 70
- 70 CHAPTER 6 DATA PAGE 71
- CHAPTER 6 DATA PAGE 71 72
- Figure 6.6 – Monthly Report 72
- 72 CHAPTER 6 DATA PAGE 73
- CHAPTER 6 DATA PAGE 73 74
- Saving a Report Template 75
- Export Tab 76
- Automated Custom Export 77
- Current Automated Export 78
- 78 CHAPTER 6 DATA PAGE 79
- CHAPTER 6 DATA PAGE 79 80
- System Page 7 82
- Status Tab 83
- Networks Tab 83
- Error Log Tab 84
- Figure 7.4 – Error Log Tab 85
- 84 CHAPTER 7 SYSTEM PAGE 85
- Users Tab 86
- Network Permissions 87
- User Privileges 87
- Settings Tab 88
- Information 89
- Mail Settings 89
- Status Settings 90
- 90 CHAPTER 7 SYSTEM PAGE 91
- Figure 7.9 – Status Settings 91
- Timer Settings 92
- Data Settings 93
- Collection Settings 94
- Database Settings 95
- Log Level 95
- Session Timeout 95
- Classes Tab 96
- Notifications Tab 97
- Journal Tab 98
- Service Tab 99
- Support Tab 101
- Figure 7.20 – Support Tab 102
- Help Page 8 104
- User Guide Tab 105
- License Info Tab 105
- License Agreement Tab 106
- Figure 8.6 – Support Tab 107
- 106 CHAPTER 8 HELP PAGE 107
- Driver Reference 9 108
- Custom Fields 110
- 3M 940 Trac Monitoring Card 111
- EIS RTMS X2/X3 112
- Autoscope 113
- Mikros Data Logger 114
- Class Mappings 115
Relacionado con productos y manuales para Software Wavetronix Command Collector (CMD-DCx) - User Guide
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales