Wavetronix Command Collector (CMD-DCx) - User Guide Manual de usuario Pagina 57
- Pagina / 117
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
56 CHAPTER 5 SENSOR CONFIGURATION PAGE
Custom ID – Allows you to change the custom text displayed for this sensor. is eld
is optional and is provided purely for additional identication information for each
sensor.
Collection Interval (sec) – Allows you to enter the interval of time between Collector’s
attempts to connect and download data for this sensor. By default, this is the same as
the sensor interval. If you would like to change this setting, uncheck the Use Sensor
Interval checkbox.
If communication to the sensor’s IP/port is inconsistent, setting a lower collection in-
terval may give Collector multiple chances at connecting and retrieving each data bin
from the sensor.
If communication to the sensor has very high latency or other overhead, setting a high-
er collection interval will allow Collector to make fewer connections and to eciently
retrieve more data packets per connection.
Sensor Interval (sec) – Shows the currently set sensor interval time, which indicates
how oen the sensor is collecting data.
Note
System administrators may need to experiment with dierent sensor and collection
interval combinations for the most optimal configuration for each sensor.
Time Zone – Allows you to set the time zone for the sensor.
DST – Allows you to choose whether or not the sensor will observe daylight savings time.
Sensor Networks – Contains each network registered on Collector. Checking a net-
work box will add the sensor to that network.
Use Advanced Collection Interval – Provides a way to schedule collection jobs to hap-
pen when needed. Checking this box will open the Advanced Collection Interval tabs.
e Basic tab allows you to enter a number and select the time units (seconds, minutes,
hours) to be used as the advanced collection interval (see Figure 5.7). Once you’ve set
the interval, click the Add button and the new collection interval will appear beneath
the box.
Figure 5.7 – Basic Tab
e Advanced tab allows you to set a start and end date, as well as a start time, for collection
(see Figure 5.8). If you don’t check the box next to the end date, the job will indenitely con-
tinue to run as scheduled. e tabs under the Repeat section can be used to set how oen
- Command Collector 1
- Contents 4
- Chapter 8 Help Page 103 5
- Introduction 6
- Data Storage 7
- Installing Command HQ 1 8
- Wavetronix representative 10
- Install button 12
- Command Licensing 13
- Oine Activation 14
- In this chapter 18
- Logging In 18
- Service Not Started Errors 19
- Common Web Interface Features 20
- Navigation/Status Control 21
- Web Interface Context Help 22
- Sensors Page 3 24
- Sensor List 25
- Network(s) 27
- Location 28
- Description 28
- Interval (Intrvl) 28
- Frequency (Fq) 28
- Figure 3.5 – Paging Control 29
- Display Settings Control 30
- Filter Controls 31
- With Com Status 32
- With Data Status 32
- Figure 3.10 – By Data Filter 33
- Sensor Toolbar 4 34
- Add Sensors 35
- Modem Support Using COM Ports 37
- Adding Ranges of Sensors 37
- Adding from an Address Book 38
- Remove Sensors 39
- View Errors 39
- Sensor Error Display Settings 40
- Sensor Error Queries 41
- Exporting Sensor Errors 41
- Collection 43
- Intervals 43
- Commands 45
- Networks 46
- Figure 4.18 – Search Box 48
- Figure 4.19 – Search Results 48
- Sensor Configuration Page 5 50
- Sensor Info Bar 51
- Com Status 52
- Data Status 52
- Communication Status Graph 52
- Data Status Graph 53
- Sensor Information 54
- View Log Button 54
- Sensor Config Tab 55
- Custom Configuration Panel 56
- Figure 5.7 – Basic Tab 57
- Figure 5.8 – Advanced Tab 58
- Lanes/Approaches Tab 59
- Setting Custom Lane IDs 60
- Approaches 60
- Sensor Commands Tab 61
- Data Query Tab 63
- Data Query Graphs 64
- Data Query Tables 65
- Data Page 6 68
- Selecting Sensors 69
- Define and Request Report 69
- Output Report Type 70
- 70 CHAPTER 6 DATA PAGE 71
- CHAPTER 6 DATA PAGE 71 72
- Figure 6.6 – Monthly Report 72
- 72 CHAPTER 6 DATA PAGE 73
- CHAPTER 6 DATA PAGE 73 74
- Saving a Report Template 75
- Export Tab 76
- Automated Custom Export 77
- Current Automated Export 78
- 78 CHAPTER 6 DATA PAGE 79
- CHAPTER 6 DATA PAGE 79 80
- System Page 7 82
- Status Tab 83
- Networks Tab 83
- Error Log Tab 84
- Figure 7.4 – Error Log Tab 85
- 84 CHAPTER 7 SYSTEM PAGE 85
- Users Tab 86
- Network Permissions 87
- User Privileges 87
- Settings Tab 88
- Information 89
- Mail Settings 89
- Status Settings 90
- 90 CHAPTER 7 SYSTEM PAGE 91
- Figure 7.9 – Status Settings 91
- Timer Settings 92
- Data Settings 93
- Collection Settings 94
- Database Settings 95
- Log Level 95
- Session Timeout 95
- Classes Tab 96
- Notifications Tab 97
- Journal Tab 98
- Service Tab 99
- Support Tab 101
- Figure 7.20 – Support Tab 102
- Help Page 8 104
- User Guide Tab 105
- License Info Tab 105
- License Agreement Tab 106
- Figure 8.6 – Support Tab 107
- 106 CHAPTER 8 HELP PAGE 107
- Driver Reference 9 108
- Custom Fields 110
- 3M 940 Trac Monitoring Card 111
- EIS RTMS X2/X3 112
- Autoscope 113
- Mikros Data Logger 114
- Class Mappings 115
Relacionado con productos y manuales para Software Wavetronix Command Collector (CMD-DCx) - User Guide
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.104 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales