Wavetronix SmartSensor 105 (SS-105) - User Guide Manual de usuario Pagina 67
- Pagina / 99
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
66 CHAPTER 6 LANE SETUP
To do this, click on the Edit Lane Name button and the Edit Lane Names window will
appear. Highlight the current lane name by double-clicking on it, then type in the lane’s
new alphanumeric identication of up to eight characters.
To reorder the lanes, you will rst need to enter a “#” sign and then the lane number. Once
you enter “#1,” for example, you can add “NB” or any other name with the remaining char-
acters.
Note
The RTMS protocol can report up to eight lanes. By default, the first zone is asso-
ciated with the lane closest to the sensor; the second zone is associated with the
next closest lane and so on. .To map the lanes in a dierent order, enter the “#”
sign followed by a unique number character between 1 and 8. (Unused lanes do not
need to be named.) The other characters are ignored but may be used for clarification
purposes. Remember, a lane with the name “#1” will be reported first in the RTMS
protocol, corresponding to zone 1; a lane with the name “#2” will be reported second,
corresponding to zone 2.
Lane names can also be changed by going to Sensor Settings and clicking on the Data
Collection tab (see chapter 7 for more information).
Saving the Configuration
Once all congurations are completed, the changes must be updated in the SmartSensor’s
ash memory (lane changes won’t take eect until after the sensor has been updated). Up-
date all manual changes by clicking the Update button located below the manual tool but-
tons (see Figure 6.6). e process of updating the conguration takes only seconds. Once
the process is completed, SmartSensor Manager will remain on the Lane Conguration
page so that any manual changes made may be viewed and easily changed if needed.
Figure 6.6 – Update, Undo, and Restart Buttons
Undoing Manual Changes
Unsaved changes may be undone without repeating the manual conguration process.
Click on the Undo button found below the manual tool buttons (see Figure 6.6). is
tool retrieves the last saved conguration from the SmartSensor, eectively undoing any
unsaved changes that were made.
- SmartSensor 105 1
- Contents 4
- Introduction 6
- SmartSensor 105 Package 7
- Selecting a Mounting Location 7
- In this chapter 12
- Center Line 13
- Figure 1.6 – Attached Cable 17
- Connecting Power and 18
- Surge Protection 2 18
- Underground 19
- Wiring to Earth Ground 21
- Wiring AC Surge Protection 23
- Connecting DC Power 25
- In the Main Trac Cabinet 26
- Wiring Communication 27
- Using SmartSensor Manager 30
- Manager 3 32
- About Screen 33
- Table of Contents 33
- Figure 3.3 – Help Screen 34
- Release Notes 35
- Communication 4 36
- Serial Connection 37
- Advanced Serial Settings 38
- Modem Connection 39
- Internet Connection 40
- Advanced Internet Settings 41
- Firmware Upload 42
- Exit SmartSensor Manager 43
- Continue w/o upload 43
- Connection Properties 44
- Address Book 45
- Using the Address Book 46
- Communication Error 47
- Sensor Settings 5 50
- Sensor Settings 51
- Figure 5.2 – General Tab 52
- Communication Tab 53
- Data Collection Tab 54
- Sensor Date & Time 57
- Operating Mode 58
- Lane Setup 6 60
- Edit Range Blinders 61
- Manage Gain 62
- Lane Configuration – Manual 63
- Paint and Remove Lines 64
- Remove Lane 64
- Construct and Remove Roads 64
- Construct and Remove Barriers 65
- Reverse Direction 65
- Edit Lane Names 66
- Saving the Configuration 67
- Undoing Manual Changes 67
- Verifying Lane Configuration 68
- Trac (Event) Data 69
- Figure 6.9 – Event Counter 70
- Figure 6.10 – Event Log 70
- Interval Data 71
- Data Collection 7 74
- Step 2: Configure the Sensor 76
- Interval Data Buer Status 76
- Data Download 77
- Download Interval Data 78
- Data Logs 79
- Figure 7.4 – Export Data Logs 81
- Tools 8 84
- CHAPTER 8 TOOLS 85 86
- Figure 8.2 – Firmware Upload 86
- Controller 89
- Contact Closures 90
- Programming Contact Closures 91
- Appendix 92
- Brown CTS 93
- Gray 232 GND 93
- Appendix C – Cable Lengths 96
Relacionado con productos y manuales para Sensores Wavetronix SmartSensor 105 (SS-105) - User Guide
(4 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales