Wavetronix SmartSensor 105 (SS-105) - User Guide Manual de usuario Pagina 78
- Pagina / 99
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER 7 DATA COLLECTION 77
Download Interval Data
Under the Download Interval Data section, click the Browse button. is will open a di-
rectory box where you can either create a new data download le log or locate an existing
download le log. Once you’ve selected an existing le or entered the name of the new le,
select Open.
Next, select the type of download to perform. e following types of download sessions are
available:
Normal – Retrieves all interval data from the beginning of the study to the most recent
record. e number of lanes per record is determined by the number of lanes currently
congured on the sensor.
Incremental – Retrieves only the interval data that was recorded after the indicated
date and time. e number of lanes per record is determined by the number of lanes
currently congured on the sensor.
Error Recovery – Retrieves the entire contents of the ash memory buer. e ash
memory buer contains 2976 records and each record has data for eight lanes. e
contents of SRAM are not retrieved in this mode. You can perform this type of down-
load to verify the contents of the ash memory buer in the event that a normal or
incremental download does not retrieve all the data that you expect to receive.
Once you have selected the type of download, click Download.
Note
Each time a data download is performed, a header is inserted into the log file that
indicates the date of the download.
Data in the SRAM buer contains the most recent information and will be downloaded
rst. If there is any data in the ash buer, it will be downloaded second. However, before
the data is written to the log le it will be reordered, so that the oldest data intervals will
be near the top of the le.
If you want to cancel the download or if you only want to download a certain number of
intervals, click the Stop button as soon as the desired number of interval data records are
downloaded. Once the download process has stopped, a window is displayed that indicates
number of interval data records that were downloaded.
- SmartSensor 105 1
- Contents 4
- Introduction 6
- SmartSensor 105 Package 7
- Selecting a Mounting Location 7
- In this chapter 12
- Center Line 13
- Figure 1.6 – Attached Cable 17
- Connecting Power and 18
- Surge Protection 2 18
- Underground 19
- Wiring to Earth Ground 21
- Wiring AC Surge Protection 23
- Connecting DC Power 25
- In the Main Trac Cabinet 26
- Wiring Communication 27
- Using SmartSensor Manager 30
- Manager 3 32
- About Screen 33
- Table of Contents 33
- Figure 3.3 – Help Screen 34
- Release Notes 35
- Communication 4 36
- Serial Connection 37
- Advanced Serial Settings 38
- Modem Connection 39
- Internet Connection 40
- Advanced Internet Settings 41
- Firmware Upload 42
- Exit SmartSensor Manager 43
- Continue w/o upload 43
- Connection Properties 44
- Address Book 45
- Using the Address Book 46
- Communication Error 47
- Sensor Settings 5 50
- Sensor Settings 51
- Figure 5.2 – General Tab 52
- Communication Tab 53
- Data Collection Tab 54
- Sensor Date & Time 57
- Operating Mode 58
- Lane Setup 6 60
- Edit Range Blinders 61
- Manage Gain 62
- Lane Configuration – Manual 63
- Paint and Remove Lines 64
- Remove Lane 64
- Construct and Remove Roads 64
- Construct and Remove Barriers 65
- Reverse Direction 65
- Edit Lane Names 66
- Saving the Configuration 67
- Undoing Manual Changes 67
- Verifying Lane Configuration 68
- Trac (Event) Data 69
- Figure 6.9 – Event Counter 70
- Figure 6.10 – Event Log 70
- Interval Data 71
- Data Collection 7 74
- Step 2: Configure the Sensor 76
- Interval Data Buer Status 76
- Data Download 77
- Download Interval Data 78
- Data Logs 79
- Figure 7.4 – Export Data Logs 81
- Tools 8 84
- CHAPTER 8 TOOLS 85 86
- Figure 8.2 – Firmware Upload 86
- Controller 89
- Contact Closures 90
- Programming Contact Closures 91
- Appendix 92
- Brown CTS 93
- Gray 232 GND 93
- Appendix C – Cable Lengths 96
Relacionado con productos y manuales para Sensores Wavetronix SmartSensor 105 (SS-105) - User Guide
(4 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.139 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales