Wavetronix SmartSensor 105 (SS-105) - User Guide Manual de usuario Pagina 89
- Pagina / 99
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
88 CHAPTER 9 CONTACT CLOSURE COMMUNICATIONS
Click 100 – e Click 100 is a din rail–mounted contact closure that can be used in
cabinets without detector racks and simplies integration into automatic data record-
ers and data loggers. e wiring harness of the automatic data recorders can connect
directly to the screw terminals of the Click 100. Application notes for wiring to com-
mon automatic trac recorders can be obtained by contacting your authorized Wa-
vetronix dealer or Wavetronix Technical Services.
Click 101 – e Click 101 has the built-in capability of collecting from multiple Smart-
Sensor units simultaneously, making it an excellent choice for midblock applications.
is allows one Click 101 to collect trac data from all the SmartSensor stations
pertaining to an intersection. For arterial management, the resulting system is very
cost-eective and can be rapidly deployed, especially when wireless communications
is included.
Each SmartSensor uses its two communication ports to send real-time trac data to
both cabinets for which it is collecting data (see Figure 9.1). e real-time data is used
to control the intersection using either local control strategies or closed-loop control
systems like ACS-lite.
Trac
Controller
Figure 9.1 – SmartSensor Sending Real-time Data to Multiple Approaches Using Dual Ports
Click 172/174 – e Click 172/174 are contact closure cards that allow the SmartSen-
sor to integrate into standard ITS and intersection detector racks. e Click 172 has
two contact closure outputs and the Click 174 has four. e Click 172/174 are com-
monly used in legacy ITS cabinets or for midblock intersection detection. Multiple
modules can be daisy-chained together to collect data from all eight lanes possible
with SmartSensor.
Unlike the Click 101, which actively collects information from multiple sensors, each
Click 172/174 is dedicated to a single sensor. During programming, the Click 172/174
cards transmit conguration information to SmartSensor to set up the mode of opera-
tion. Once the mode is set up, the rack cards stop transmitting messages and passively
listen for data pushed by the sensor.
- SmartSensor 105 1
- Contents 4
- Introduction 6
- SmartSensor 105 Package 7
- Selecting a Mounting Location 7
- In this chapter 12
- Center Line 13
- Figure 1.6 – Attached Cable 17
- Connecting Power and 18
- Surge Protection 2 18
- Underground 19
- Wiring to Earth Ground 21
- Wiring AC Surge Protection 23
- Connecting DC Power 25
- In the Main Trac Cabinet 26
- Wiring Communication 27
- Using SmartSensor Manager 30
- Manager 3 32
- About Screen 33
- Table of Contents 33
- Figure 3.3 – Help Screen 34
- Release Notes 35
- Communication 4 36
- Serial Connection 37
- Advanced Serial Settings 38
- Modem Connection 39
- Internet Connection 40
- Advanced Internet Settings 41
- Firmware Upload 42
- Exit SmartSensor Manager 43
- Continue w/o upload 43
- Connection Properties 44
- Address Book 45
- Using the Address Book 46
- Communication Error 47
- Sensor Settings 5 50
- Sensor Settings 51
- Figure 5.2 – General Tab 52
- Communication Tab 53
- Data Collection Tab 54
- Sensor Date & Time 57
- Operating Mode 58
- Lane Setup 6 60
- Edit Range Blinders 61
- Manage Gain 62
- Lane Configuration – Manual 63
- Paint and Remove Lines 64
- Remove Lane 64
- Construct and Remove Roads 64
- Construct and Remove Barriers 65
- Reverse Direction 65
- Edit Lane Names 66
- Saving the Configuration 67
- Undoing Manual Changes 67
- Verifying Lane Configuration 68
- Trac (Event) Data 69
- Figure 6.9 – Event Counter 70
- Figure 6.10 – Event Log 70
- Interval Data 71
- Data Collection 7 74
- Step 2: Configure the Sensor 76
- Interval Data Buer Status 76
- Data Download 77
- Download Interval Data 78
- Data Logs 79
- Figure 7.4 – Export Data Logs 81
- Tools 8 84
- CHAPTER 8 TOOLS 85 86
- Figure 8.2 – Firmware Upload 86
- Controller 89
- Contact Closures 90
- Programming Contact Closures 91
- Appendix 92
- Brown CTS 93
- Gray 232 GND 93
- Appendix C – Cable Lengths 96
Relacionado con productos y manuales para Sensores Wavetronix SmartSensor 105 (SS-105) - User Guide
(4 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales